|Home||» Products||» Paints & Coatings||» Aluma Silicon 540 C High Temperature Paint|
Aluma Silicon 540 C High Temperature Paint
- Minimum Order Quantity
- No minimum order quantity
- Unit of Measure
- Minimum Order Quantity
- FOB Port
- ASHDOD ISRAEL
- Payment Terms
- Cash Advance (CA), Cash in Advance (CID), Letter of Credit (L/C), Paypal
- Delivery Time
- 7 days after payment in ASHDOD port or BEN gurion airport Days
- Sample Available
- Sample Policy
- Free samples are available
- Packaging Details
- in case in carton boxes pallets
- Main Export Market(s)
- Middle East
- Main Domestic Market
- All India
Aluma Silicon 540 C High Temp. Paint
Organic modified Aluma Silicon 540 C High Temperature Paint shows high temperature resistant property up to 540°C. Its development is based on combustion silicones to withstand mainly high temperatures for guarding varied surfaces of concrete, iron, etc. from very high temperatures up to 540°C.
Swift to dry top coat paint
Exceptional adherence to chimneys, ovens, etc. of iron or concrete
Economical and can be used in only one thin 15-25 microns layer
Humid and damp resistant
Withstand 540 degrees Celsius
Can be used to a Zinc Silicate base to acquire an anticorrosive system that is resistant to high temperatures.
Coating of magnesium plants, ovens, enamel, ceramics, and so on that develop high heat
Hot gas and vapor spewing systems
Industrial steam chimneys
Large light reflectors painting for utmost light return
Painting marginal metals, particularly hot burning heat security for varied industries working with exceptional heat.
Painting walls as well as metal surfaces in the melting pants of steel
Piping transporting hot liquids
Water and oil boilers
Consumption: 125 microns
Density: 1.1-1.15 gm/cm3
Flexibility: l mm (SHEEN).
Hardness: >3 Dg (Erickson) After heating in oven at 200°C during 50 seconds.
Recommended layer thickness 15-25 microns each layer dry film.
Recommended number of layers: 2
Solids content: 20 %
Theoretically area covered: 1 liter for 8 m2 •
Viscosity: 0.2-0.5 (HAAKE).
High temperature Aluminum powder
Special organic silicon combustion resins
Touch dry time: 6 hours
Drying between layers
Final hardness is attained after 7 days
Spray and brushing
If non uniform material is there and behaves like mercury owing to high inner pressure stress, then paint the surface, wait for 60 seconds and then paint again until a smooth surface is attained
It is suggested to blend the paint well before as well as during painting
Spraying: 0-5% thinner D and -21 pressure 4-5 atm. (can apply without thinning)
Brushing/roller: 5% (can apply without thinning)
Airless: 0-5% thinner D-21 pressure 5-6 atm. 0.015” nozzle (can apply without thinning)
Chemical or technical cleansing is done until metal remains white
Chemical: rust remover 3000 and grease/oils degreaser M
Mechanical: grade ST3 steel brushes
Sand blasting grade: SA 2.5
Iron metals: zinc silicate
Other metals: use primer paint accurately to ensure steady adherence
At room temperature in shaded and protected place having proper ventilation
Keep the lids closed tightly
D-21 instantly after finish painting
In house quality testing lab as per specifications
ISO 9001-2008, COA and COC certificate
As it is inedible, so keep away from children.
It is flammable; hence keep away from fires, flames, heated areas, and sparks
Do not smoke near it or in working area
Good air ventilation should be there while applying. If there is not enough air, use ventilation as per the ventilation table.
Wear safety suits, glasses and gloves
Avoid direct paint contact with the skin and eyes. Immediately wash thoroughly in case of any contact
Immediately call doctor in case of any injury
Read all safety instructions carefully on the labels and also see M.S.D.S
Don’t mix it with any product that is not recommended
Don’t apply under +7°C temperature
Don’t apply over 80% humidity
While applying without air, never throw it on anybody as a direct hit can be fatal at pressures of more than 150 atm.
Read carefully all the technical data listed in the section and for any clarification, you can contact to our tech. department.
All the listed information is a recommendation only and cannot be used in the court of law.
The costumer must examine & check that the availed product is attuned with his demands and equipment.
The listed information in this section is given as per the laboratory conditions (temperature, humidity etc.) that the products were checked.
The recommendations listed do not hold any accountability for this product.
Theoretical and actual coverage area are different concepts, the genuine coverage is affected by the necessary thickness of the layers, requisite number of layers, conditions of painting including the quantity of paint that spread in the air prior touching the surface.
The information of this section is based on understanding and accumulating data, we have the right to modify the information any time.
Paints that are in stagnant position or exposed to air more than requirement can change their qualities.
Store at 15°C to 25°C temperature
Over Spray: Dust is created by dry gases of the air that causes the paint particles to fall on the surface. The impact becomes stronger owing to over pressure and heat. To evade the negative effect, the pressure of the spraying must be lowered to the essential minimum. A different possibility is to augment the amount of the thinner that cause the paint particles to fall wetter on the surface.
An additional suggested possibility is to add a retarder to enhance the time of painting application, hence increases the drying up time, and enabling it to reach the surface wetter
Pot Life: The working time that is possible to paint a mixture of two components, without spoiling the properties of the paint or disqualifying the paint.
Spray: A sprayer with a container to hold paint can be used to spray with air pressure.
Airless: a device having a piston to compresses the air for spraying paints.
Surface preparations: the level of cleanness is judged by international standards. This process comprises cleansing sand blasting to attain optimal results for painting adhesion. These standards are evenly compared to the Swiss SA, the German-Din the U.S SSPC SP standards. For each standard, there are indicators to make visual contrast between the surface cleansing and the indicator.
Prior to large surfaces’ painting, it is essential to test the product on a small area to ensure that the paint is attuned with the level of satisfactory.
Laboratory testing is done as per the standards institution specifications.
This "Data sheet" specified as noncommittal information, the product is recommended for specialized painting specialists. This information is not an alternate to personal guidance.
You should read the MSDS safety instructions carefully before start working with the product.