Cookie Img
Home » Products » Paints & Coatings » Anti Rust Paint

Anti Rust Paint

Anti Rust Paint
Anti Rust Paint
Product Code : 59
Product Description

Zinkcoat 022 Anti Rust Paint

Paint enriched with zinc and aluminum for coating metal/ steel for a long lasting rust prevention. An excellent hot galvanization substitute, that doesn’t need to be heated,. Has excellent endurance in harsh conditions, doesn’t allow rust development even in humid and salty environments when coated with a synthetic, polyurethane or chromed rubber top paint.

Properties :

  • Provides cathodic protection that prevents rust development for many years.
  • Has an excellent adhering ability.
  • Contains the optimum amount of zinc.
  • Beautiful and bright silver color.
  • Dries fast within a day.
  • Top paint is applicable within 16 hours.
  • Has firm and high erosion endurance in harsh conditions and industrial environments.
  • Has excellent protection ability against rust.

Applications :

  • For coating metals with zinc (cold galvanization).
  • Renewing damaged galvanization.
  • Fast galvanization in field conditions.
  • High quality primer for top paints.
  • Cold galvanization for large objects such as metal buildings.

Technical  specifications:

  • Coverage area: 10 sqm.  per liter.
  • Recommended layer thickness:  100 microns.
  • Amount of zinc within a dry film: at least 90%
  • Density: 1.9-2.1 gm/cm3
  • Flexibility: 2 mm (SHEEN)
  • Viscosity: 1-2Pas,sec (HAAKE)
  • Hardness: over 3 Dg (Ericson)

Contains:

  • Selected synthetic resins.
  • Formaldehyde melamine.
  • Pure powered zinc.
  • Aluminum.
  • Diluters and additives.

Shade:

Metallic grey.

Gloss:

Matte.

Touch-dryness:

  • 40-60 minutes.
  • If  dust is formed while spraying add a retarder .
  • Drying time period between layer application:
  • 16 hours.  Final:  24 hours.

Application methods:

Brush, spray, roll.

Dilution:

  • Brush or roller: 5% - 10% D-18 thinner.
  • Spraying: 15% - 25%  3-4 atm.
  • Airless 0% - 5% 4-5 atm. Nozzle 0.018”

Surface preparations:

  • Remove grease and rust until receiving a clean metal.
  • Mechanically clean with a steel brush.
  • Sand blast until reaching Sa 2.5 level.
  • Chemically clean:  rust with rust remover 3000,  grease: degreazer M.

Packaging:

0.75 liter, 1 liter, 2.5 liter, 5 liters, 18 liters.

Storage:

In a shaded and cool place at room temperature.

Shelf Life:

12 months in its original package.

Equipment cleansing:

Use D-18 thinner immediately after usage ..

Quality control:

  • In factory laboratories according to specifications.
  • COA and COC certificate.
  • ISO 9001-2008

Safety precautions:

  • Inedible, keep away from the reach of children.
  • Flammable – keep distant from heated areas, fires, flames, and sparks, Prohibit smoking in working area.
  • While applying, good air ventilation is important. In case there is not enough air, use ventilation according to the ventilation table.
  • Wear protective glasses, gloves and suits.
  • Avoid direct contact of the paint and/or thinner with the eyes and skin. In case of contact, immediately wash thoroughly with water.
  • In case of an injury immediately get doctors assistance.
  • Read the safety instructions on the labels.
  • See M.S.D.S

Warnings:

  • Don’t mix the product with materials which were not recommended by us.
  • Don’t apply if the temperature is under +7°C .
  • Don’t apply if humidity is over 80%
  • When applying with Airless, do not aim it at anybody a direct hit could be fatal at pressures over 150 atm.
  • Read thoroughly the technical data of the product listed in this section; confirm that everything is understood completely, for clarification contacts our tech. department.
  • All information that is listed in this content is a recommendation merely and can not  be applied in the court of law.
  • The costumer must test & check that this product is compatible with his equipment and needs. 
  • The information listed in this section is according to the laboratory conditions (temperature, humidity etc.) which the products were tested.
  • The recommendations listed do not hold any responsibility for this product.
  • Theoretical and actual coverage area are different concepts, the actual coverage is affected by the required thickness of the layers, required number of layers, painting conditions including the amount of paint which spread in the air before touching the surface.
  • The information listed in this section is based on experience and accumulating data, Denber inc., has the right to change the information listed at any time.
  • Paints that have been in stagnation or exposed to air more than needed could have their qualities changed.

Clarifications:

  • Storage room temperature 15°C to 25°C .
  • Over Spray: An effect which occurs in the spraying of paints application. A type of  "dust" is created by dry gases  of the air, which causing the paint particles to fall dry on the surface (hereafter the "effect"). The impact of this "effect" becomes stronger due to over pressure and heat, (most sprayers have a lever to control the   pressure) To avoid the negative impact 0f the "effect", the pressure of the spraying should be lowered to the necessary minimum!. Another possibility is to increase the amount of the thinner in the mixture which would cause the paint particles to fall wetter on the surface.
  • An additional recommended possibility, to avoid this "effect", is to add a retarder to the mixture which increases the duration period of the painting application , avoiding the paint to  dry up, and enabling it to reach the surface wetter, Thus a better painted smooth  layer is formed.
  • Pot Life : The working time which is possible to paint a mixture of two components, A+B (or more) without spoiling the qualities of the paint or disqualifying the paint as "out  of use".
  • Spray: It is possible to spray with a sprayer that has a container holding the paint that sprays it with air pressure.
  • Airless: a device with a piston which compresses the air for spraying paints. The pressure might be high (over 100atm.) Don't aim it at anyone
  • Surface preparations: the level of cleanness is determined by international standards. Surface  preparations, including cleansing sand blasting, is important & critical factor in achieving an optimal  results for painting adhesion on a certain  surface. These standards are equally compared to the standards of the Swiss SA, the German-Din the U.S SSPC SP       For each standard in any level there are indicators, for sale,  in order to make visual comparison between the cleansing of the surface and the indicator.

Quality inspection:

  • Prior to the painting on large surfaces it is important to test the product on a small area, to be sure that the paint is compatible with the level of satisfactory.
  • Laboratory testing was made according to the standards institution specifications.
  • This "Data sheet" given as noncommittal information, the product above recommended for professional painting specialists. This information is not a substitute to personal guidance.
  • You must read the MSDS safety instructions before you start working with the product.

DENBER PAINTS AND COATINGS ISRAEL LTD.

Contact Us

( *represents compulsory fields )

Tips on getting accurate quotes. Please include product name, order quantity, usage, special requests if any in your inquiry.



DENBER PAINTS AND COATINGS ISRAEL LTD. All Rights Reserved.