|Home||» Products||» Paints & Coatings||» Bacterinol Bio Anti Bacterial Emulsion Paint|
Bacterinol Bio Anti Bacterial Emulsion Paint
- Minimum Order Quantity
- No minimum order quantity
- Unit of Measure
- FOB Port
- ASHDOD ISRAEL
- Payment Terms
- Cash Advance (CA), Cash in Advance (CID), Letter of Credit (L/C), Paypal
- Delivery Time
- 7 days after payment in ASHDOD port or BEN gurion airport Days
- Sample Available
- Sample Policy
- Free samples are available
- Packaging Details
- in case in carton boxes pallets
- Main Export Market(s)
- Middle East
- Main Domestic Market
- All India
Unique acrylic Bacterinol Bio - Anti Bacterial Emulsion Paint is available to kill and prevent fungus, rot as well as mold development. This also provides complete protection from serious infectious diseases such as MRSA, swine flu, E. coli bacteria, etc. It prevents the development of bacteria causes mildew and odors.
Tested and approved in the UK laboratories IMSL MICROBIOLOGOCAL SERVICES LTD . Test No. 1013627,55 / 4515 Test No. 1013627,49 / 4510
Anti-bacterial, kills bacteria and prevents diseases, acts as a catalyst paralyzing the enzyme used in oxygen metabolism of bacteria, viruses (viruses) and fungus (are single-celled and can not exist in his environment) and are killed.
Prevents mold, rot, fungus, mildew, odors
Odorless, water-based, easy to apply.
Blocks moisture and allows evaporation ("breathing wall")
Very washable and durable scrubbing
Excellent adhesion capacity infrastructure
White and shades.
Flexibility - 1 mm (Sheen)
Hardness - 3 Dg (Ericsson)
Erosion - 120 micron - 500 cycles (BYK Gardner) ASTM
Scrubbing resistance - minimum 200 cycles according to Israeli Standard 1945
Suggested layer thickness - 40-60 microns.
Multiple layers recommended - 2-3.
Density - 1.4-1.5 gm \ cm3
Coverage - 1 liter to 5-10 m2
Viscosity - 7-11 Pa.sec (Haake)
Fungicides, pure silver, preservatives.
Fine acrylic emulsion.
Materials for superior flexibility.
Self-Leveling wetting materials.
Thixotropic film and other additives.
UV resistance improvers.
Bright white and other shades as per Standard Dnbercryl catalogue.
Catalog of 1000 shades.
Dry to the touch:
Add water and reduce air pressure if "dust" was created during splattering
Drying between layers:
Final 12 hours.
First layer - 20-30%
Second layer - 5-20%
Clean from dust, grease, dirt and loose paint.
Renew external wall with pressure of 150 atm.
Fill holes and cracks using Denber Acrylic Schpachtel
Spray primer Denberol super.
If the old paint is peeled off, take it away completely and spread Denbercryl 4000 diluted 30% with water.
If the wall is deteriorating – use a layer of denbertex primer.
Renewing interior walls – seal holes and cracks using denberschpachtel and sand with sandpaper and spread Denberol or better smear layer of Denbercryl 4000.
Internal wall - Denberol super or Denbercryl 400,
External wall - Denberol super or Denbercryl 4000
Old and crumbling external wall with primer "Denbertex Primer".
At room temperature in cool shaded and protected place having proper ventilation
Keep the lids closed tightly
Water and soap
In house quality testing lab as per specifications
ISO 9001-2008, COA and COC certificate
As it is inedible, so keep away from children.
It is flammable; hence keep away from fires, flames, heated areas, and sparks
Do not smoke near it or in working area
Good air ventilation should be there while applying. If there is not enough air, use ventilation as per the ventilation table.
Wear safety suits, glasses and gloves
Avoid direct paint contact with the skin and eyes. Immediately wash thoroughly in case of any contact
Immediately call doctor in case of any injury
Read all safety instructions carefully on the labels and also see M.S.D.S
Don’t mix it with any product that is not recommended
Don’t apply under +7°C temperature
Don’t apply over 80% humidity
While applying without air, never throw it on anybody as a direct hit can be fatal at pressures of more than 150 atm.
Read carefully all the technical data listed in the section and for any clarification, you can contact to our tech. department.
All the listed information is a recommendation only and cannot be used in the court of law.
The costumer must examine & check that the availed product is attuned with his demands and equipment.
The listed information in this section is given as per the laboratory conditions (temperature, humidity etc.) that the products were checked.
The recommendations listed do not hold any accountability for this product.
Theoretical and actual coverage area are different concepts, the genuine coverage is affected by the necessary thickness of the layers, requisite number of layers, conditions of painting including the quantity of paint that spread in the air prior touching the surface.
The information of this section is based on understanding and accumulating data, we have the right to modify the information any time.
Paints that are in stagnant position or exposed to air more than requirement can change their qualities.
Store at 15°C to 25°C temperature
Over Spray: Dust is created by dry gases of the air that causes the paint particles to fall on the surface. The impact becomes stronger owing to over pressure and heat. To evade the negative effect, the pressure of the spraying must be lowered to the essential minimum. A different possibility is to augment the amount of the thinner that cause the paint particles to fall wetter on the surface.
An additional suggested possibility is to add a retarder to enhance the time of painting application, hence increases the drying up time, and enabling it to reach the surface wetter
Pot Life: The working time that is possible to paint a mixture of two components, without spoiling the properties of the paint or disqualifying the paint.
Spray: A sprayer with a container to hold paint can be used to spray with air pressure.
Airless: a device having a piston to compresses the air for spraying paints.
Surface preparations: the level of cleanness is judged by international standards. This process comprises cleansing sand blasting to attain optimal results for painting adhesion. These standards are evenly compared to the Swiss SA, the German-Din the U.S SSPC SP standards. For each standard, there are indicators to make visual contrast between the surface cleansing and the indicator.
Prior to large surfaces’ painting, it is essential to test the product on a small area to ensure that the paint is attuned with the level of satisfactory.
Laboratory testing is done as per the standards institution specifications.
This "Data sheet" specified as noncommittal information, the product is recommended for specialized painting specialists. This information is not an alternate to personal guidance.
You should read the MSDS safety instructions carefully before start working with the product.