|Home||» Products||» Paints & Coatings||» Denway Road Marking Paints|
Denway Road Marking Paints
- Minimum Order Quantity
- No minimum order quantity
- Unit of Measure
Denway Road Marking Paints
Solvent dilution, smooth as well as decorative Denway Road Marking Paints are ideal for asphalt and concrete roads. It is also used for sidewalks with outstanding adhesion to infrastructure. They are very strong and tough pain used for outdoor extreme conditions such as heat, cold, sunlight (U.V.) etc. They are white in color with high durability standards and shades (yellow, black. blue, red and orange). They are perfect for much vehicular traffic night and day.
Abrasion and scratched proof
Can fill the cracks in asphalt and concrete.
Can penetrate deep into the grooves
Durable in the heat
Easy to apply
Excellent adhesion capacity
Flexible and rigid
High coverage area
Highly durable in outdoor conditions.
Perfectly water resistant
Ready for repainting at the same day
Resistant to fuels
Striking paint that can be seen from great distance
Suitable for winter heavy rains
Road marking asphalt
Concrete paint for urban roads
Marking sidewalks and parking lots.
Painting pedestrian crossings.
Bleeding durability: not less than level 6 (ASTM D-868 and ASTM D-969)
Consumption for new asphalt road: 1 liter for 1.3-2.0 sqm. as per asphalt quality.
Consumption for old asphalt road: 1 liter for 2.0 sqm.
Density: 1.45-1.6 gm/cm3
Durability in solvents and fuels: ASTM D-2792-93
Durability in water immersion: no bubbles, no softening, no changes in adhesion, (Israel standard 935 chapter 312)
Erosion 120 mic. film – 1560 cycles (BYK Gardner), americn standard ASTM D4060 - 200 mic. film, loss of weight 2 gr. To 500 cycles (2.5 alloud)
Flexibility: l mm (Sheen). (standard 935 part 307)
Grinding : < 50 micron (standard 785 part 15 - < 60 mic.)
Hardness: >10 Dg (Erickson)
Pigments quantity: 65% (standard 785 part 19)
Quantity of glass beads: 100-150 gr. /sqm.
Recommended layer thickness 200 microns wet layer.
Recommended number of layers: 1
Solids content by volume: > 70 % (standard 785 part 17)
Theoretically area covered: 1 liter for 10 sqm. Hiding ability minimum 0.9 (Israel standard 935 part 306)
Viscosity: 1.5-2.5 Pa.sec (Haake) 78-92 krebs in 200 cycle/minutes after blending for 2 minutes by hand (standard 935 part 302) after dilution 10% with thinner – 65 krebs. After 10 days storage in 42 OC – viscosity will grow < 5 krebs.
Wetting and leveling materials.
< 18% (Israel standard 935 part 309)
Touch dry time:
15 min. (a very quick drying paint, avoid over spray)
Drying time with a wheel is < 45 minutes
In case of over spray – add retarder as required and decrease air pressure
Time to open road for driving:
Summer : 30 min.
Winter: 45 minutes.
Methods of application:
Concrete: spray, brush, roller.
Brush/roller: 5% thinner D-18
Airless: 0-5% thinner D-18, nozzle 0.018” for thin layer and nozzle 0.021” for thick layer.
Spraying: 20-30% thinner D-18 pressure 3-4 atm.
Remove any dirt, grease, dust, or loose paint before coating
Wash and brush using Degreezer Z – to remove oils
Clean as per standard of 935.
At room temperature in shaded and protected place having proper ventilation
Keep the lids closed tightly
Employ thinner D-18 at the end of painting
In house quality testing lab as per specifications
ISO 9001-2008, COA and COC certificate
As it is inedible, so keep away from children.
It is flammable; hence keep away from fires, flames, heated areas, and sparks
Do not smoke near it or in working area
Good air ventilation should be there while applying. If there is not enough air, use ventilation as per the ventilation table.
Wear safety suits, glasses and gloves
Avoid direct paint contact with the skin and eyes. Immediately wash thoroughly in case of any contact
Immediately call doctor in case of any injury
Read all safety instructions carefully on the labels and also see M.S.D.S
Don’t mix it with any product that is not recommended
Don’t apply under +7°C temperature
Don’t apply over 80% humidity
While applying without air, never throw it on anybody as a direct hit can be fatal at pressures of more than 150 atm.
Read carefully all the technical data listed in the section and for any clarification, you can contact to our tech. department.
All the listed information is a recommendation only and cannot be used in the court of law.
The costumer must examine & check that the availed product is attuned with his demands and equipment.
The listed information in this section is given as per the laboratory conditions (temperature, humidity etc.) that the products were checked.
The recommendations listed do not hold any accountability for this product.
Theoretical and actual coverage area are different concepts, the genuine coverage is affected by the necessary thickness of the layers, requisite number of layers, conditions of painting including the quantity of paint that spread in the air prior touching the surface.
The information of this section is based on understanding and accumulating data, we have the right to modify the information any time.
Paints that are in stagnant position or exposed to air more than requirement can change their qualities.
Store at 15°C to 25°C temperature
Over Spray: Dust is created by dry gases of the air that causes the paint particles to fall on the surface. The impact becomes stronger owing to over pressure and heat. To evade the negative effect, the pressure of the spraying must be lowered to the essential minimum. A different possibility is to augment the amount of the thinner that cause the paint particles to fall wetter on the surface.
An additional suggested possibility is to add a retarder to enhance the time of painting application, hence increases the drying up time, and enabling it to reach the surface wetter
Pot Life: The working time that is possible to paint a mixture of two components, without spoiling the properties of the paint or disqualifying the paint.
Spray: A sprayer with a container to hold paint can be used to spray with air pressure.
Airless: a device having a piston to compresses the air for spraying paints.
Surface preparations: the level of cleanness is judged by international standards. This process comprises cleansing sand blasting to attain optimal results for painting adhesion. These standards are evenly compared to the Swiss SA, the German-Din the U.S SSPC SP standards. For each standard, there are indicators to make visual contrast between the surface cleansing and the indicator.
Prior to large surfaces’ painting, it is essential to test the product on a small area to ensure that the paint is attuned with the level of satisfactory.
Laboratory testing is done as per the standards institution specifications.
This "Data sheet" specified as noncommittal information, the product is recommended for specialized painting specialists. This information is not an alternate to personal guidance.
You should read the MSDS safety instructions carefully before start working with the product.
- FOB Port
- ASHDOD ISRAEL
- Payment Terms
- Cash Advance (CA), Cash in Advance (CID), Letter of Credit (L/C), Paypal
- Delivery Time
- 7 days after payment in ASHDOD port or BEN gurion airport Days
- Sample Available
- Sample Policy
- Free samples are available
- Packaging Details
- in case in carton boxes pallets
- Main Export Market(s)
- Middle East
- Main Domestic Market
- All India